|
#1
05-25-2008, 08:50 PM
|
|||
|
|||
|
#@$% $%^&*(
I just twisted off two of the six screws that hold the tuning discs on. Sombitch !!!!!!!!!!!!!!!!!!!!!!!!!!!! now I am gonna have to get em out. SHIET !!!!!!!!!!!
 :ba dmood::badmood ::bad mood: :badm ood:
|
|
#2
05-25-2008, 09:18 PM
|
|||
|
|||
|
|
|
#3
05-25-2008, 09:27 PM
|
|||
|
|||
|
Just like a bull in a china cabinet is what my Momma always said>
Just sayin:  Deep breaths-----deep breaths>
|
|
#4
05-25-2008, 09:41 PM
|
|||
|
|||
|
Putting them in or taking them out?
If it was putting them in, you way over TQ them, The discs act like lock washers and provide tension to keep the screws from backing out. Did you use Anti seize on them?? You are suppose to. Did they snap off at the thread or on the shaft? If on the shaft, just take the other out, take the discs off and get out your favorite pair of vise grips. If at the thread, well 4 screws should work unless the one that broke were right next to each other. You and Rick should never tighten anything without a TQ wrench on it. Don't know you own strength. And you have that nice set of TQ wrenches too. Say, it you are not going to use them, can I have them.
|
|
#5
05-26-2008, 06:42 AM
|
|||
|
|||
|
taking them out. both twisted off flush
gonna have to drill and retap, to small to try an ez out.
|
|
#6
05-26-2008, 06:52 AM
|
||||
|
||||
|
Quote:
__________________
there's a little bit of dog in every one of us - Mike, just a GazintA, joined this sane asylum on the 37th day of 2007 
|
|
#7
05-26-2008, 07:48 AM
|
|||
|
|||
|
Quote:
If this is a new pipe, I would be talking to SuperTrapp about it.
|
|
#8
05-27-2008, 03:37 PM
|
||||
|
||||
|
Sorry bout the bad news.
What's the update?
__________________
     Introducing the Al Gore engine Obsolete Doof 1998 Obsolete Springer Rider Part time Shovel Rider Some time XLCH Kicker 
|
|
#9
05-27-2008, 03:58 PM
|
|||
|
|||
|
upon trying to drill out I discovered that the screw inserts are made out of what I believe is lead ?!?!? too soft for aluminum.. the drill bit kept sliding off the tiny ass screw into the lead.... any who... I couldnt drill them out so I punched the twisted screws in and out, then retapped with a 1/4 inch tap and bought new screws. Its good to go.
|
|
#10
05-27-2008, 04:00 PM
|
|||
|
|||
|
man... I was afraid to open this thread... didn't want to read that you weren't coming...
Isn't it just louder if ya leave the damned things out...?
|
|
#11
05-27-2008, 04:07 PM
|
||||
|
||||
|
Quote:
|
|
#12
05-27-2008, 04:08 PM
|
|||
|
|||
|
Apparently, you don't know your own strength.
|
|
#13
05-27-2008, 04:12 PM
|
||||
|
||||
|
Quote:
__________________
there's a little bit of dog in every one of us - Mike, just a GazintA, joined this sane asylum on the 37th day of 2007
|
|
#14
05-27-2008, 04:20 PM
|
||||
|
||||
|
Dog you dam well better be here the 6th of July. I'll make sure there are clean linens on the bed.
Don't make me come down there and get you!
__________________
Randy                  *Sensitive at all times.
|
|
#15
05-27-2008, 07:01 PM
|
||||
|
||||
|
Quote:
__________________
 April 13, 2016 -- The day Richard was speechless. May your hands always be busy, May your feet always be swift. May you have a strong foundation When the winds of changes shift. May your heart always be joyful, and may your song always be sung, May you stay forever young! --Bob Dylan
|
 |
|
|
Linear Mode
